Heath-zenith Instant Motion Sensor Light Control SL-5211 Manuel d'utilisateur télécharger pdf

Mode: On-Time: Works: Day Night

Test 5 Sec x x

Auto 1, 5 or 10 min x

Manual Until Dawn* x

Features

• Turns on lighting when motion is detected.

• Automatically turns lighting off.

• Photocell keeps the lighting off during daylight hours.

Requirements

• The Light Control requires 120-volts AC.

• If you want to use Manual Override, the control must be

wired through a switch.

• Some codes require installation by a qualified elec-

trician.

OPERATION

Instant Motion Sensor

Light Control

Model SL-5211

Parts

The SL-5211 package includes:

• The Sensor and Lamp Module

• Two mounting screws

Lamp

Module

Existing Light

Fixture

Sensor

Module

Sensor

Cord

Typical Installation

The lamp module is not weather tight. It should only be

used inside of a light fixture.

10 5 1 TEST

ON-TIME

TEST

* resets to Auto Mode at dawn.

ON-TIME

AUTO

10 5 1 TEST

MANUAL MODE

... back on.

1 Second OFF

then...

Mode Switching Summary

MANUAL MODE

AUTO

TEST

* If you get confused while switching modes, turn the power

off for one minute, then back on. After the calibration time

the control will be in the AUTO mode.

Move ON-TIME Switch to

1, 5, or 10 minutes

Flip light switch off

for one second then

back on*

Note: When first turned on wait about 1

minutes for the

circuitry to calibrate.

Put the ON-TIME switch on the bottom of

the sensor in the TEST position.

Put the ON-TIME switch in the 1, 5, or 10

minute position.

Manual mode only works at night be-

cause daylight returns the sensor to

AUTO.

Flip the light switch off for one second

then back on to toggle between AUTO

and MANUAL MODE.

Manual mode works only with the ON-

TIME switch in the 1, 5, or 10 position.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Light Control

Page 2 - INSTALLATION

2595-4238-07INSTALLATION.❒ Before proceeding with the installation, TURN OFFTHE POWER TO THE LIGHTING CIRCUIT AT THECIRCUIT BREAKER OR FUSE BOX to avo

Page 3 - SPECIFICATIONS

3595-4238-07TEST AND ADJUSTMENT❒ Turn on the circuit breaker and light switch.SPECIFICATIONSRange . . . . . . . . . . . . Up to 60 feet (varies with s

Page 4 - TECHNICAL SERVICE

4595-4238-07POSSIBLE CAUSE1. A sensor is positioned too close to the lamp orpointed at nearby objects that cause heat totrigger the sensor. (Repositio

Page 5 - DECORATIVO SENSOR

5595-4238-07Modalidad: A tiempo: Trabaja: Día NochePrueba 5 seg. x xAutom. 1, 5 ó 10 min. xManual Hasta el amanecer* xCaracterísticas• Prende la luz c

Page 6 - INSTALACION

6595-4238-07Bucle CaídoIMPORTANTE: Si el cable del detector sale por la partesuperior de la instalación fija, asegúrese de que la instalaciónse cierr

Page 7 - ESPECIFICACIONES

7595-4238-07Apunte el detectormás arriba paramayor coberturaApunte el detectorhacia abajo parapoca coberturaDetectorMovimientoMovimientoLo menos sensi

Page 8 - SERVICIO TÉCNICO

8595-4238-07SINTOMALa luz seprendedurante el día.La luz seprende sinninguna razónaparente.La luz seprende y seapaga.POSIBLE CAUSA1. El Control de Luz