Heath Zenith 2LBL7 Manuel d'utilisateur télécharger pdf

Gasket

(Optional)

Mounting

Bracket

Photocontrol

Ground

Screw

Fixture

Lamp

Temporary

This ﬁxture can be mounted on a wall with, or without using a ﬂush-

mounted junction box. Do not attempt to mount this ﬁxture on a

surface-mounted “Wet Location” junction box. Use the instructions

below that apply to your application.

Installation Using A Junction Box

Note: If your junction box protrudes out of the wall slightly, you may

want to use the enclosed gasket so less caulking is required.

1. Hold the Mounting Bracket and Gasket over the junction box.

Thread the supply wires through the large hole in the back of

the Mounting bracket. Select the holes in the mounting bracket

that line up with the screw holes in the junction box. Make sure

the bottom of the Mounting Bracket is level. Secure with the two

#8 screws provided.

Installation Without A Junction Box

1. Select a location on a ﬂat wall with structurally sound wood and

from 5 to 25 feet from the ground. The wood should be at least

one inch thick to safely secure the ﬁxture.

2. Use the Mounting Bracket as a template. Hold it at the desired

mounting location (making sure the bottom is level), and mark

four mounting holes.

3. Use four #8 or #10 wood screws or galvanized deck screws at

least 1 inch long (not provided) to secure the Mounting Bracket

to the wall. It may be necessary to drill appropriate pilot holes if

mounted to hardwood to avoid splitting.

4. Remove the knockout in the bottom of the Mounting Bracket, and

bring your supply wires through this knockout using appropriate

ﬂexible conduit or other approved means of wiring.

Complete The Installation

Put the Temporary Pin through the holes in the Mounting Bracket.

2. This ﬁxture must be grounded. Connect the supply ground wire to

the green ground screw. You can also attach a bare or green “pigtail”

to the green ground screw, then connect the ground pigtail to the

supply ground when the other supply wires are connected.

3. Slide the ﬁxture onto the Mounting Bracket, and allow the ﬁxture

to rest on the Temporary Pin.

4. Connect the ﬁxture wires to the supply wires (black to black,

white to white, and if a ground pigtail was added above, con-

nect this pigtail to the supply ground wire). Secure with the wire

connectors provided.

5. Remove the Temporary Pin, and slide the ﬁxture all the way down

onto the Mounting Bracket making sure no wires get pinched.

6. Install the screw through the bottom of the Mounting Bracket and

into the ﬁxture housing. Tighten this screw.

7. Install lamp (provided). Lamp rating must match the rating of the

ﬁxture.

Model 2LBL7: 50 watt metal halide M110/O open rated lamp.

Model 2LBL8: 70 watt high pressure sodium type S62 lamp.

8. Caulk ﬁxture mounting surface with silicone weather sealant.

To test operation during daylight, cover the photocontrol with black

tape. Turn on the power. The light will take up to ten minutes to reach

full brightness. Remove the tape from the photocontrol and your unit

will operate automatically—on at dusk, off at dawn.

WARNING: Turn power off at the fuse or circuit

breaker.

Model 2LBL7: 50 Watt Metal Halide Patio Light

Model 2LBL8: 70 Watt High Pressure Sodium Patio Light

NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or

another acceptable means. Contact a qualiﬁed electrician if there is any question as to the suitability of the system.

Operating Instructions & Parts Manual 2LBL7, 2LBL8

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain

the product described. Protect yourself and others by observing all safety information. Failure to comply could

result in personal injury and/or property damage! Save these instructions for future reference.

598-1319-02

LPG-5659, LPG-5679

HEA 012

Printed in China

02/08

Lamp in Fixture Contains Mercury. Dispose According

to Local, State, or Federal Laws.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Printed in China

Gasket (Optional)MountingBracketPhotocontrolGround ScrewFixtureLampTemporary PinThis ﬁxture can be mounted on a wall with, or without using a ﬂush-mou

Page 2 - Model 2LBL7

10598-1319-021. Retirez le couvercle de plastique.2. Retirez l’ampoule.3. Retirez les 5 vis qui ﬁxent le réﬂecteur au boîtier du luminaire.4. Étiq

Page 3 - Model 2LBL8

11598-1319-021. Retirez le couvercle de plastique.2. Retirez l’ampoule.3. Retirez les 5 vis qui ﬁxent le réﬂecteur au boîtier du luminaire.4. Étiq

Page 4 - 1 YEAR LIMITED WARRANTY:

12598-1319-02GARANTIE LIMITÉE D’UN AN :En cas de défaillance de ce produit attribuable à un défaut de fabrication au cours de l’année suivant la date

Page 5

2598-1319-02LampSocketPhotocellSocketIgnitorBallastLargeCoilSmallCoilRedRedBlack120V ACInputBlackBlackBlueWhiteWhiteWhiteWhiteWhiteWhiteWhite1. Remov

Page 6 - Modelo 2LBL7

3598-1319-02Ballast Assembly Replacement InstructionsModel 2LBL8Lamp Socket Photocell Socket Ballast Ignitor Red Red Red Black Black Blue Blue White

Page 7 - Modelo 2LBL8

4598-1319-021 YEAR LIMITED WARRANTY:Should this product fail to perform satisfactorily due to a defect or poor workmanship within one year of date of

Page 8 - Lake Forest, IL 60045

5598-1319-02NOTA: Todo el cableado debe ser tendido de acuerdo al Código Eléctrico Nacional (Código Eléctrico Canadiense en Canadá) por tubería u otro

Page 9

6598-1319-021. Retire la cobertura plástica.2. Retire la bombilla.3. Retire los cinco tornillos que sujetan el reﬂector a la caja del artefacto.4.

Page 10 - Modèle 2LBL7

7598-1319-021. Retire la cobertura plástica.2. Retire la bombilla.3. Retire los cinco tornillos que sujetan el reﬂector a la caja del artefacto.4.

Page 11 - Modèle 2LBL8

8598-1319-02GARANTÍA LIMITADA A UN (1) AÑO:Si este producto fallara en funcionar satisfactoriamente debido a un defecto o mala fabricación dentro de u

Page 12 - GARANTIE LIMITÉE D’UN AN :

9598-1319-02Ce luminaire peut être monté sur un mur, avec ou sans boîte de jonction afﬂeurante. N’essayez pas d’installer ce luminaire sur une boîte d

Commentaires sur ces manuels

Pas de commentaire

Heath Zenith 2LBL7 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Heath Zenith 2LBL7. Heath Zenith 2LBL7 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Heath Zenith 2LBL7